Carl Bernosky, 8-time winner of the Camp Perry National High Power Championships, will be switching back to a bolt gun for the 2009 competition. Last year, Carl shot an AR15-based spacegun built on Smith & Wesson M&P15 components. With that rifle, Carl became the first competitor to win the Camp Perry High Power Championship shooting an AR15-type semi-auto.

But this year Carl will be shooting a 6.5 Creedmoor CSR-1 TubeGun from Creedmoor Sports. Based on a TubeGun Chassis and buttstock by Gary Eliseo (of Competition Shooting Stuff), the CSR-1 features a Pierce Precision Rem 700-clone receiver, and a 28″ Broughton barrel.

Both the buttstock and the handguard are adjustable to suit the shooter. The handguard/float tube can rotate 15 degrees from center in either direction, allowing the shooter to adjust his desired rifle cant. The 4-way buttstock adjusts for length-of-pull, cant, buttpad height and offset. There is an adjustable cheekpiece and even two 4.8-ounce removeable weights to allow precise balancing of the rig.

The CSR-1 is offered in five (5) chamberings: 308 Win, 6.5 Creedmoor, 6.5×47 Lapua, 6XC, and .223 Rem. At Camp Perry, Carl Bernosky will be shooting a 6.5 Creedmoor version of the rifle, using Hornady components.

CLICK HERE to learn more about specs and features of CSR-1 ($3750.00 complete).

The 2010 edition of the Hodgdon® Annual Manual has just been announced, and should be at newstands in January 2010. Now in its 7th year, the Hodgdon Annual Manual includes over 5,000 rifle and pistol loads, with information on 56 Hodgdon, IMR® and Winchester® powders. The new 2010 Manual features 44 cartridge updates, brand new data for the 6.5 Grendel and 6.5 Creedmoor, and updated propellant burn rate and usage charts.

Extensive reloading information is provided for popular cartridges such as the 17 Remington, 223 Remington, 204 Ruger, 6PPC, 308 Winchester, 338 Federal and more. In addition, the 2010 Manual includes articles by top gun writers like Layne Simpson and Jim Carmichael plus many other resources for shooters and reloaders.

Articles in the 2010 Hodgdon Annual Manual spotlight the new varmint/match powder, IMR 8208 XBR. Test lots of this new powder have shown truly exceptional temperature stability. In addition, IMR 8208 XBR should deliver excellent accuracy in cartridges such as the 6mm PPC, 6BR, 22BR, and .308 Winchester. Lou Murdica and Jim Carmichael have already recorded impressive benchrest wins with prototype IMR 8208 XBR.

The 2010 Hodgdon Annual Manual costs $8.99 and should be available at newsstands and gun dealers by January 2010. For more on the manual contact Hodgdon at 913-362-9455, visit Hodgdon.com, or write to 6231 Robinson, Shawnee Mission, KS 66202.

The 2011 Snipers’ Hide Cup took place from April 7 to 9 at the Rifles Only facility in Kingsville, Texas. The popular three-day tactical competition, organized by SnipersHide.com, featured a rich prize table with thousands of dollars worth of scopes and tactical gear. The match drew 63 of the nation’s best tactical marksmen in the civilian, law enforcement and military communities. The multi-stage event places competitors in a number of tactical scenarios with shooting out to 1000 yards. The vast majority of the shooting is done with rifles, but there is some pistol action also. This year, the match format involved “a lot of run and gun, positional, and movers”. The wind played a major role this year, exceeding 24 mph on some stages.

CLICK HERE for More Photos from 2011 Snipers’ Hide Cup

Top Two Finishers Use 6.5 Creedmoor
The overall match winner was Geordie Richardson of Weatherford, TX (via Australia), with a score of 1385/2300. Geordie shot well on nearly every stage, staying in the top three throughout the competition. One fellow competitor remarked: “I was two spots down from [Richardson] and watched the magic happening. He couldn’t miss.” Geordie’s match-winning rifle was a Surgeon Rifles Scapel chambered in 6.5 Creedmoor in a Sentinel stock with Atlas bipod. On top was a S&B 5-25x56mm with Gen2 XR reticle. Geordie shot Hornady factory 6.5 Creedmoor ammo, as did runner-up Tate Moots, as well as the fourth place and seventh place finishers.

Charles “Tate” Moots (Team FNH) took second place overall with a score of 1305/2300 points. Moots used a FN SPR A5M bolt-action rifle, chambered in 6.5 Creedmoor and topped with a Leupold 6.5×20 ERT scope. Finishing third was John Sommers, fourth was Rob Ormond, and taking fifth was George Gardner of GA Precision.

Match runner-up Moots was top finisher in the exciting Helicopter Stage, which required each competitor to engage a ground target from a flying helicopter with an FN SCAR 17S, and upon landing exit the aircraft and fire a five shot group with their precision rifle. Shown below is a helicopter stage from the 2010 Snipers’ Hide Cup. (Turn sound volume down at work.)

Frank Galli, aka “Lowlight”, runs the popular SnipersHide.com website. Frank recently completed a gunsmithing course with Robert Gradous. Frank recounts the learning process in an informative, nicely-illustrated article on the ‘Hide. Frank explains how he put together a new 6.5 Creedmoor tactical rifle using a Bartlein barrel, Bighorn Action (Rem clone with floating bolt-head), and a “lightly used” Accuracy International 1.5 chassis. The HD video below shows the process start-to-finish. READ Full Article.

During Frank’s “hands-on” training sessions with Gradous, Frank learned to thread and chamber a barrel, fit a recoil lug, and install the barreled action in the AI chassis. Chambering was done with great care: “We spent the better part of the day working the barrel. I feel this is a critical component and seeing the attention to detail in Robert’s approach confirmed it for me. When it came time to chamber Robert had a custom tight chamber reamer there for a 6.5CM but I’m shooting a tactical rifle, tight chambers aren’t for me, and this was clear, as out came the standard SAAMI reamer.”

Frank also learned how to modify an aluminum chassis: “the AI chassis had the recoil lug opened up, but it was opened in the wrong direction. This was going to require milling increasing the gap to at least a 1/2″ in size. Robert was really leery of this, but my attitude was, ‘it’s just a chassis and nothing a little Marine Tex can’t handle’.” Thankfully the chassis mod came out OK.

Once the barreled action was complete and the AI chassis was successfully milled, Frank applied a tan Cerakote finish to the barreled action. This would give a proper tactical look to the rifle, while providing superior corrosion resistance for the metal parts. To learn more about Cerakote finishing, check out the Cerakote Application Video, published last week in the Daily Bulletin.

When the rifle was complete, Frank took it out for testing with a variety of ammo, both factory fodder and handloads. There were some initial worries about accuracy as it took a while for the barrel to break in. A few sessions of bore cleaning were required before the barrel stopped fouling and then — like magic — the rifle started printing really small groups.

By the end of his load testing session, Frank was getting good groups with Hornady 120gr GMX factory 6.5 Creedmoor ammo, and really superb groups with handloads. The 120gr GMX ammo “was going 3100 fps with no ill effects”. The best handloads were approaching 1/4 MOA for three shots, and Frank’s load with Berger 130 VLDs shot even smaller than that: “In my opinion the load development we did was worth its weight in gold. Where else can you build in a rifle in two days, then go out and develop a baseline load using everything from 120gr ammo to 140gr ammo with a few in between? My favorite load and clearly the rifle’s too, was the [Berger] 130gr VLD. This gave us great velocity, awesome groups [with some one-holers] and really nice results at distance.”

Lowlight’s Gunsmithing Story is a ‘Must-Read’
We recommend you read Frank’s story. It shows that, with the right tools, and the supervision of a master smith, even a novice can produce an ultra-accurate rifle. For those of you who have considered taking a gunsmithing class, Frank’s successful experience with gunsmith Robert Gradous should give you plenty of motivation.

CLICK HERE to Read Lowlight’s Gunsmithing Course Article
CLICK HERE for Info on Gradous Rifles Gunsmithing Class

The August 2011 digital edition of Shooting Sports USA is now available online — free for the reading. This month’s issue contains a “must-read” expert symposium on Eye Dominance, as it affects both rifle and pistol shooting. No matter whether you have normal dominance (i.e. your dominant eye is on the same side as your dominant hand), or if you have cross-dominance, you’ll benefit by reading this excellent article. The physiology and science of eye dominance is explained by Dr. Norman Wong, a noted optometrist. In addition, expert advice is provided by champion shooters such as David Tubb, Lones Wigger, Dennis DeMille, Julie Golob, Jessie Harrison, and Phil Hemphill.

Development of the 6.5 Creedmoor Cartridge
Also in the August Edition of Shooting Sports is a feature on the 6.5 Creedmoor cartridge. This story covers the origin of the cartridge and its performance both as a match cartridge and as a hunting round. Hornady Chief Ballistician Dave Emary explained: “the original intent of the cartridge was as an across-the-course match cartridge. We envisioned it as an off-the-shelf round that would produced the accuracy and ballistics to compete in all match disciplines right out of the box. At the same time we realized that the same characteristics would make an exceptional hunting cartridge with the right bullets.”

6.5 Creedmoor Brass No Longer Washed After Annealing
Here’s an interesting update on Hornady 6.5 Creedmoor brass and loaded ammo. In a move to improve case quality and neck uniformity, Hornady recently changed the 6.5 Creedmoor production process, eliminating the case-washing step after annealing. So now you will see annealing coloration on 6.5 Creedmoor brass, just like on Lapua brass. Dennis DeMille of Creedmoor Sports wanted to improve the consistency/uniformity of 6.5 Creedmoor case-necks. At Dennis’ suggestion, Hornady conducted tests which showed that the “standard industry practice” of washing brass could potentially alter the necks in undesirable ways. Bottom line, unwashed annealed brass was determined to have an accuracy edge over washed brass. Looking at these results, Hornady decided to forgo the post-anneal washing process. As a result, the latest 6.5 Creedmoor brass now displays the distinctive coloration left by neck/shoulder annealing. Learn something new every day, eh?

While the 6.5 Creedmoor cartridge was devised primarily for High Power and Across the Course shooters, it has also found favor with tactical shooters looking for a highly accurate round that feeds well from a magazine, but offers significantly less recoil than a .308 Winchester. In fact, the 6.5 Creedmoor has become so popular that some vendors we checked were sold out of both brass and loaded ammo. (Don’t worry though — Creedmoor Sports has both 6.5 Creedmoor brass and loaded ammo in stock.)

CLICK HERE for 6.5 Creedmoor Video and Specifications

6.5 Creedmoor vs. 6.5×47 Lapua — Cost Factor
The 6.5×47 Lapua and 6.5 Creedmoor offer very similar ballistics with 120gr and 140gr bullets. However, 6.5 Creedmoor brass AND loaded ammo are cheaper. That’s a big plus in the tactical game. At tactical competitions, there are “move and shoot” stages where you need to shoot quickly and then move to another position. It’s very difficult to recover all your brass. Losing a piece of 6.5×47 brass (at $1 dollar a pop) is painful. The Hornady brass is $34.49 per 50 (69 cents each) at Sinclair Int’l or $34.95 per 50 (70 cents each) at Creedmoor Sports.

Hornady’s 6.5 Creedmoor loaded ammunition is also much less expensive than the loaded 6.5×47 Lapua rounds. For shooters that don’t have the time (or skills) to reload, the 6.5 Creedmoor (at $25.95 per 20-rd box) makes more financial sense. Grafs.com currently sells loaded 123gr 6.5×47 Lapua ammo for $52.79 per 20 rounds.

On the other hand, the Lapua brass is tougher. Forum member Mudcat observes: “[As to] the Hornady brass, while it’s good, it ain’t no Lapua, so don’t try to run hot loads cause all you are going to do is blow out the primer pockets. Keep your loads reasonable and you will get over 20 loads out of em. I have some I have loaded well over 20 times during testing…they grow like a mother though, as they are a lot softer than Win or Lapua, which is why the pockets will go. However the necks haven’t been splitting.”

Barrel Life Looks Promising
Barrel life appears to be pretty good with the 6.5 Creedmoor. Barrels will last significantly longer than with a typical .243 Win or 6.5-284. Forum Member Mudcat reports: “Based on my throat wear at 600 rounds on my 6.5 Creedmoor barrel, I bet we are looking at 2500 rounds EASY of great accuracy and then probably to at least 3000 where you ain’t going to notice it shooting Cross the Course — you might see something at 600, but nothing worse than a few less Xs. At 600 rounds, I have not had to move my VLD seating depth yet.” Forum member Rob1, who shoots tactical comps with Team Blaster, notes that Hornady puts its load and velocity on every box (see photo below), so it’s easy for reloaders to duplicate the factory ammo. That way you can start with a few boxes of factory fodder, and then load your own.

We often get questions about the 6.5 Creedmoor Cartridge — folks ask where they can find good resources for this cartridge, which is popular with Across-The-Course, High Power, and tactical shooters. We did some searching and found that the August 2011 digital edition of Shooting Sports USA has a good article for all fans of the 6.5 Creemoor.

Development of the 6.5 Creedmoor Cartridge
In the August 2011 Edition of Shooting Sports USA you’ll find a lengthy feature on the 6.5 Creedmoor cartridge. This story covers the origin of the cartridge and its performance both as a match cartridge and as a hunting round. Hornady Chief Ballistician Dave Emary explained: “the original intent of the cartridge was as an across-the-course match cartridge. We envisioned it as an off-the-shelf round that would produced the accuracy and ballistics to compete in all match disciplines right out of the box. At the same time we realized that the same characteristics would make an exceptional hunting cartridge with the right bullets.”

6.5 Creedmoor Brass No Longer Washed After Annealing
Here’s an interesting update on Hornady 6.5 Creedmoor brass and loaded ammo. In a move to improve case quality and neck uniformity, Hornady recently changed the 6.5 Creedmoor production process, eliminating the case-washing step after annealing. So now you will see annealing coloration on 6.5 Creedmoor brass, just like on Lapua brass. Dennis DeMille of Creedmoor Sports wanted to improve the consistency/uniformity of 6.5 Creedmoor case-necks. At Dennis’ suggestion, Hornady conducted tests which showed that the “standard industry practice” of washing brass could potentially alter the necks in undesirable ways. Bottom line, unwashed annealed brass was determined to have an accuracy edge over washed brass. Looking at these results, Hornady decided to forgo the post-anneal washing process. As a result, the latest 6.5 Creedmoor brass now displays the distinctive coloration left by neck/shoulder annealing. Learn something new every day, eh?

You’ve probably heard of the 6.5 Creedmoor, an excellent round for High Power and tactical applications. Well there’s a 6mm (.243) version of this cartridge — the 6mm Creedmoor. It has the same external dimensions (other than neck diameter) as the 6.5 version, but it lets you shoot the High-BC 6mm bullets at higher velocities. With a long barrel, you can push 105gr bullets an honest 3070-3100 fps with this cartridge. The 6mm Creedmoor has a large primer pocket and large flash hole (unlike Lapua’s 6.5×47 which has a small primer pocket, and small flash hole — like the 6mmBR).

6mm Creedmoor Brass
If you’re interested in the 6mm Creedmoor, Hornady-brand brass is available right now at reasonable prices. Yesterday, GA Precision received 110,000 pieces of 6mm Creedmoor brass. Prices are:

$65.00 for 100 pieces
$325.00 for 500 pieces
$620.00 for 1000 pieces

That works out to sixty-two cents per unit if you buy 1000 cases. CLICK HERE to Order.

We have not tested the 6mm Creedmoor cartridge yet, but we know some shooters have had good luck with it. In design, the 6mm Creedmoor is quite similar to the 6XC, which is a proven High Power cartridge that has won many championships. If you want a mid-size 6mm cartridge, with brass that doesn’t cost $1.00 per case, the 6mm Creedmoor may be an option to consider. GA Precision says this about the cartridge: “The 6mm Creedmoor is an ideal cartridge for large-platform, semi-auto rifle for shooters who wish to utilize the long, high-BC modern 6mm projectiles. Compared to the .243 Winchester, the 6mm Creedmoor case is just under .130 of an inch shorter, perfect for the confines of a short-OAL AR-style magazine. This is an ideal cartridge for competitive shooters — charges easily reach 3050-3100 FPS while coming closer to the 100% volume capacity for powder charge, often resulting in lower standard deviations recorded.”

Norma is making a big push to expand its presence in the North American market. As part of this effort, Norma is introducing seven (7) new types of cartridge brass for 2014. We’re pleased to report that Norma-USA will be importing top-quality brass for the 6.5 Grendel, and 6.5 Creedmoor, two popular target cartridges. In addition, for 2014, Norma will offer 7mm RUM, 7mm Blaser Magnum, 300 AAC Blackout (300 BLK), .300 RUM, and the .338 Blaser Mag. The Norma brass we have shot in other chamberings (6 PPC, 6mmBR Norma, 6XC, .243, 7mm RSAUM) has all been excellent, giving good accuracy. Case weights were very consistent and the neck-wall thickness was very uniform, particularly with the PPC and BR brass. The new 300 BLK brass is an important offering for AR shooters. (NOTE: You can also make 300 BLK cases from Norma or Lapua .221 Fireball brass).

Though the annealing “shadow” may not be as visible as with Lapua brass, the case necks of Norma brass cartridges are indeed annealed near the end of the manufacturing process. This assures more consistent neck tension — something critical to accuracy. Most of the new cartridge brass offerings should be be available at vendors by early April, 2014. You can get Norma brass from Bullets.com, Grafs.com and Midsouth Shooters Supply, as well as many other online vendors.

New Norma-USA Brass Offerings for 2014:

It’s not easy to place a first shot on target at 1500 yards. You must measure the wind speed with precision, know your exact muzzle velocity, and have a sophisticated ballistics solver. In this short video from Ryansrangereport.com, the shooter manages a first-round hit on a steel silhouette at 1500 yards. He used a Kestrel 4500 NV Weather Meter with Applied Ballistics software to figure out the trajectory for his 6.5 Creemoor rounds.

The Kestrel recorded a wind velocity, and the internal software calculated a solution of 17 Mils elevation (that’s 928 inches of drop) with 2.5 Mils windage. “Bang” — the shooter sends it, and 2.6 seconds later “Clang” he had a hit (flight time was 2.6 seconds). Bryan Litz observes: “This is the science of accuracy (in the form of an Applied Ballistics Kestrel) being put to good use at 1500 yards”.

Later in the video (1:05-1:15) the shooter places three rounds on steel at 1000 yards in just 10 seconds. The three shots all fall within 10″ or so — pretty impressive for rapid fire. The shooter reports: “[In my 6.5 Creedmoor] I’m using a 136gr Lapua Scenar L. This bullet has impressed me. It screams out of my barrel at 2940 fps and holds on all the way out to 1,500 yards.”

The rifle was built by Aaron Roberts of Roberts Precision Rifles (RPRifles.com). Chambered for the 6.5 Creedmoor, it features a Leupold Mark VI 3-18x44mm scope.

Roberts Precision Rifles
19515 Wied Rd. Suite D
Spring, Texas 77388
Phone: 281-651-5593
Email: rprifles @ gmail.com

The .260 Remington and the 6.5×55 Swedish (aka 6,5x55mm SE) are both very popular cartridges with hunters and target shooters. The 6.5×55 has a long military heritage and a great record as a hunting round. The .260 Rem, essentially a .308 Win necked down to .264 caliber, is a more recent cartridge, but it grows in popularity every year, being one of the top cartridges for tactical/practical competitions. It offers better ballistics and less recoil than the parent .308 Win cartridge. In our Shooter’s Forum, respected UK gun writer Laurie Holland provided a good summary of the differences between the two chamberings. Laurie writes:

The 6.5×55 case has 6 or 7% more capacity than the .260s, even more in practice when both are loaded to standard COALs with heavy bullets, which sees them having to seated very deep in the .260 Rem using up quite a lot of powder capacity. So loaded up for reasonable pressures in modern actions, the 6.5×55 will give a bit more performance.

The issue for many is what action length is available or wanted, the 6.5×55 requiring a long action. So sniper rifle / tactical rifle competitors will go for the .260 Rem with the option of the many good short-bolt-throw designs around with detachable box magazines (DBMs). If a bit more performance is needed, the .260 AI (photo right) can yield another 100-150 fps velocity, depending on bullet weight.

Brass-wise, you’ve got really good Lapua 6.5×55 off the shelf that needs minimum preparation, and it’s strong and long-lived. [Editor: And now Lapua offers strong, high quality .260 Rem brass that’s every bit as good as Lapua’s 6.5×55 brass. Norma offers quality .260 Rem brass also. Both foreign brands are far better than the old Remington-brand .260 Rem brass.]

For purely target shooting, I think I’d go with 6.5×55 if I was making the choice again today for performance and brass-preparation reasons. In fact, I’ve considered going back to the gunsmith to have the barrel rechambered.

You want a multi-purpose rifle though and that makes things trickier depending on the bullet weight(s) you want to use. The [typical] 6.5×55 and 6.5-08 throats are really designed for 140s, so 90-120s make a long jump into the rifling. If you’re always going to use 130s and up, it’s less of an issue. If you want to use the lighter stuff, I’d say go for .260 Rem and discuss the reamer with the gunsmith to come up with as good a compromise as you can depending on the mix of shooting. 1:8.5″ twist is the norm and handles all the usual sporting and match bullets; you can go for a little slower twist if you won’t use the heavies.

Over here in the UK, in Scotland to be precise, we have a top sporting rifle builder (Callum Ferguson of Precision Rifle Services) who almost specializes in .260 Rem usually built on Borden actions. He throats the barrel ‘short’ so it’s suited to varmint bullets, but will still handle the 100gr Nosler Partition which he says is more than adequate for any British deer species including Scottish red stags.

Accuracy-wise, I don’t think there’s anything between them if everything else is equal. The 6.5 has a reputation for superlative accuracy, but that was high-quality Swedish military rifles and ammunition matched against often not-so-high-quality military stuff from elsewhere. Put the pair in custom rifles and use equally good brass and bullets and you’ll be hard pressed to tell them apart.” – Laurie Holland

After Laurie’s helpful comments, some other Forum members added their insights on the .260 Rem vs. 6.5×55 question:

“To me, the .260 Remington has no advantage over the 6.5×55 if one is going to use a long action. Likewise, the only advantage the .260 has in a modern rifle is it can be used in a short-action. There is more powder capacity in the 6.5×55 so you have the potential to get more velocity plus there is a lot of reloading data available to you for loading at lower velocity/pressure if you choose. The Lapua brass is great and Winchester brass is pretty good at low pressures. Having loaded a good bit for both, the 6.5×55 would always get the nod from me. To me, if someone wants to use a short-action, the 6.5×47 Lapua is even a better option than the .260 for a target rifle.” — Olympian

“There is just one small item that has been missing from this conversation — the 6.5×55 has a non-standard rim diameter of .479″ vs. the standard .473″ of a .308 and all of its variants. Depending on your bolt this may be an issue, or it may not.” — Neil L.

Other 6.5mm Contenders: 6.5×47 Lapua and 6.5 Creedmoor vs. .260 Rem
by Laurie Holland
Since I wrote those words some time back, I’ve acquired the three small contenders – .260 Rem, 6.5X47L, and most recently the 6.5mm Hornady Creedmoor and started doing load development and comparative tests. All three rifles have match-length barrels (28 or 30-inch 1:8s) — two NZ True-Flites and on the .260, a 30-inch 5R Bartlein.

How the barrel is throated is a key issue with this trio. In my case, I have always had the feeling that the .260 Rem and 6.x5x47L are at their best with 120-130 grain bullets and both have been chambered to suit the 123gr Scenar seated optimally. Both shoot this bullet fantastically well at getting on for 3,000 fps using Vihtavuori N150. I’m constantly amazed by this bullet’s external ballistics performance at up to 900 yards. I’ve yet to try it at 1,000. No, you won’t stand up to someone shooting a 7 WSM or .284 Shehane with 180gr Hybrids or VLDs at 900 or 1,000 in rough conditions in an F-Open match, but that applies to the 6.5-284 too.

I’m very taken with all three cartridges. The 6.5×47 Lapua is an outstanding mid-range number IMHO. The .260 a good all-rounder. But I have a ‘feeling’ that I am going to end up very fond of the Creedmoor and can understand its tremendous success in the USA. Over here in the UK, it barely registers with target shooters, and I doubt if at all with what US shooters call ‘hunters’, we call ‘deerstalkers’. Fortunately, I was able to get 300 pieces of Hornady brass a couple of years ago, but we can get very strong Lapua .22-250 Rem cases here easily and they can be necked-up / fire-formed albeit to produce a slightly short-necked 6.5 HCM.”

Article by Bill, Editor of Rifleshooter.com
A few years ago I built a custom switch-barrel Remington 700 on an AICS Chassis chambered in .243 Winchester and .308 Winchester. I found the .243 Win finicky during load development and started looking at other options for the 6mm Bartlein 1:8″-twist HV barrel.

Initially drawn to the 6mmBR and 6mm Dasher, I realized these cartridges wouldn’t feed from an AICS magazine system without extensive modification. I took a look at the 6mm Creedmoor, 6XC, and 6mm-6.5×47 Lapua (aka 6×47 Lapua), all of which feed well from a detachable magazine. At right you can see the 6×47 Lapua in an AICS magazine. It has the “Goldilocks factor” — not too long, not too short.

The ability to simply convert 6.5×47 Lapua brass to 6×47 brass by running the parent 6.5mm brass through a full-length Forster sizing die in a single step was what made me choose the 6×47 Lapua over the 6mm Creedmoor and 6XC (both excellent cartridges in their own right). I also own a 6.5×47 Lapua rifle, so I had a supply of 6.5×47 brass ready to neck-down. Being able to create 6×47 brass easily (one pass and done) was very appealing.

Left to right, below: 6mmBR, 6-6.5×47 Lapua, 6.5×47 Lapua, and .243 Winchester.

I cut the chamber end off my .243 Win barrel, threaded and chambered my rifle for the 6×47 Lapua cartridge. I have written a lengthy article on this cutting and re-chambering process. Home gunsmiths interested in this process can READ MORE HERE.

When the re-chambering was complete, I headed to the range and worked up a set of eight loads using Berger 108 BTHPs, H4350, Lapua brass, and CCI 450 primers.

Load development was a little trickier than with the 6.5×47 Lapua parent cartridge. The accuracy nodes were smaller. However, once I dialed in a load with Hodgdon H4350 and the 108-grain Berger BTHP, the rest was history. The 6×47 rig is now one of the most consistent rifles I own, holding just above 0.3 MOA for 5-round groups. Below is a 100-yard test target with 108-grain Berger BT in the 6×47 Lapua. Five-shot group sizes are (L to R): .369″, .289″, and .405″. The average size was .354″ or .338 MOA. [Editor: We think that is excellent accuracy for a tactical-type rifle shot from bipod.]

Learn More about this 6×47 Lapua Project
I’ve written more about this 6×47 rifle on my Rifleshooter.com website. To learn more about my experience with the 6×47 Lapua, click this link: 6-6.5X47 Lapua Review.

We often get questions about the 6.5 Creedmoor Cartridge — folks ask where they can find good resources for this cartridge, which is popular with Across-The-Course, High Power, and tactical shooters. We did some searching and found that the August 2011 digital edition of Shooting Sports USA has a good article for all fans of the 6.5 Creedmoor.

Development of the 6.5 Creedmoor Cartridge
In the August 2011 Edition of Shooting Sports USA you’ll find a lengthy feature on the 6.5 Creedmoor cartridge. This story covers the origin of the cartridge and its performance both as a match cartridge and as a hunting round. Hornady Chief Ballistician Dave Emary explained: “the original intent of the cartridge was as an across-the-course match cartridge. We envisioned it as an off-the-shelf round that would produced the accuracy and ballistics to compete in all match disciplines right out of the box. At the same time we realized that the same characteristics would make an exceptional hunting cartridge with the right bullets.”

6.5 Creedmoor Brass No Longer Washed After Annealing
Here’s an interesting update on Hornady 6.5 Creedmoor brass and loaded ammo. In a move to improve case quality and neck uniformity, Hornady recently changed the 6.5 Creedmoor production process, eliminating the case-washing step after annealing. So now you will see annealing coloration on 6.5 Creedmoor brass, just like on Lapua brass. Dennis DeMille of Creedmoor Sports wanted to improve the consistency/uniformity of 6.5 Creedmoor case-necks. At Dennis’ suggestion, Hornady conducted tests which showed that the “standard industry practice” of washing brass could potentially alter the necks in undesirable ways. Bottom line, unwashed annealed brass was determined to have an accuracy edge over washed brass. Looking at these results, Hornady decided to forgo the post-anneal washing process. As a result, the latest 6.5 Creedmoor brass now displays the distinctive coloration left by neck/shoulder annealing. Learn something new every day, eh?

What do you get when you cut a 6.5 Creedmoor-chambered barrel down to just over 16 inches? A lot more velocity than you might think. Our friends at Rifleshooter.com recently did a barrel cut-down test with 6.5 Creedmoor test rifle, shortening the barrel from 27 to 16.1 inches in one-inch increments. Surprisingly, with a 142gr Sierra MK, the total velocity loss (as measured with a Magnetospeed) was just 158 FPS, an average of 14.4 FPS per inch of barrel length. With the lighter 120gr A-Max bullet, the total velocity loss was 233 FPS, or 21.8 FPS average loss per inch of barrel.

CLICK HERE to SEE All Velocity Values at All Barrel Lengths

To perform this velocity test, our friend Bill, Rifleshooter.com’s editor, built up a 6.5 Creedmoor rifle using a Remington Model 7 action, 1:8″ twist Green Mountain CM barrel, and MDT LSS Chassis, all obtained from Brownells.com.

Test Procedure
Five (5) rounds of each type of cartridge were fired at each barrel length and the velocity data was recorded with a MagnetoSpeed V3 barrel-mounted chronograph. The rifle was then cleared and the barrel was cut back one inch at a time from 27″ to just over 16″. NOTE: During this winter test, the air temperature was a very chilly 23° F. One would expect higher velocities across the board had the outside temperature been higher.

Read Full Story with All Test Results at Rifleshooter.com

The photo below shows how the barrel was cut down, inch-by-inch, using a rotary saw. The barrel was pre-scored at inch intervals. As the main purpose of the test was to measure velocity (not accuracy) the testers did not attempt to create perfect crowns.

6.5 Creedmoor vs. Other Mid-Sized 6.5mm Cartridges
The 6.5 Creedmoor is a very popular cartridge with the tactical and PRS crowd. This mid-size cartridge offers good ballistics, with less recoil than a .308 Winchester. There’s an excellent selection of 6.5mm bullets, and many powder choices for this cartridge. When compared to the very accurate 6.5×47 Lapua cartridge, the 6.5 Creedmoor offers similar performance with less expensive brass. For a tactical shooter who must sometimes leave brass on the ground, brass cost is a factor to consider. Here’s a selection of various 6.5 mm mid-sized cartridges. Left to right are: 6.5 Grendel, 6.5×47 Lapua, 6.5 Creedmoor with 120gr A-Max, 6.5 Creedmoor with 142gr Sierra MK, and .260 Remington.

When asked to compare the 6.5 Creedmoor to the 6.5×47 Lapua, Rifleshooter.com’s editor stated: “If you don’t hand load, or are new to precision rifle shooting, get a 6.5 Creedmoor. If you shoot a lot, reload, have more disposable income, and like more esoteric cartridges, get a 6.5×47 Lapua. I am a big fan of the 6.5×47 Lapua. In my personal experience, the 6.5×47 Lapua seems to be slightly more accurate than the 6.5 Creedmoor. I attribute this to the quality of Lapua brass.”

The .260 Remington and the 6.5×55 Swedish (aka 6,5x55mm SE) are both very popular cartridges with hunters and target shooters. The 6.5×55 has a long military heritage and a great record as a hunting round. The .260 Rem, essentially a .308 Win necked down to .264 caliber, is a more recent cartridge, but it grows in popularity every year, being one of the top cartridges for tactical/practical competitions. It offers better ballistics and less recoil than the parent .308 Win cartridge. In our Shooter’s Forum, respected UK gun writer Laurie Holland provided a good summary of the differences between the two chamberings. Laurie writes:

The 6.5×55 case has 6 or 7% more capacity than the .260s, even more in practice when both are loaded to standard COALs with heavy bullets, which sees them having to seated very deep in the .260 Rem using up quite a lot of powder capacity. So loaded up for reasonable pressures in modern actions, the 6.5×55 will give a bit more performance.

The issue for many is what action length is available or wanted, the 6.5×55 requiring a long action. So sniper rifle / tactical rifle competitors will go for the .260 Rem with the option of the many good short-bolt-throw designs around with detachable box magazines (DBMs). If a bit more performance is needed, the .260 AI (photo right) can yield another 100-150 fps velocity, depending on bullet weight.

Brass-wise, you’ve got really good Lapua 6.5×55 off the shelf that needs minimum preparation, and it’s strong and long-lived. [Editor: And now Lapua offers strong, high quality .260 Rem brass that’s every bit as good as Lapua’s 6.5×55 brass. Norma offers quality .260 Rem brass also. Both foreign brands are far better than the old Remington-brand .260 Rem brass.]

For purely target shooting, I think I’d go with 6.5×55 if I was making the choice again today for performance and brass-preparation reasons. In fact, I’ve considered going back to the gunsmith to have the barrel rechambered.

You want a multi-purpose rifle though and that makes things trickier depending on the bullet weight(s) you want to use. The [typical] 6.5×55 and 6.5-08 throats are really designed for 140s, so 90-120s make a long jump into the rifling. If you’re always going to use 130s and up, it’s less of an issue. If you want to use the lighter stuff, I’d say go for .260 Rem and discuss the reamer with the gunsmith to come up with as good a compromise as you can depending on the mix of shooting. 1:8.5″ twist is the norm and handles all the usual sporting and match bullets; you can go for a little slower twist if you won’t use the heavies.

Over here in the UK, in Scotland to be precise, we have a top sporting rifle builder (Callum Ferguson of Precision Rifle Services) who almost specializes in .260 Rem usually built on Borden actions. He throats the barrel ‘short’ so it’s suited to varmint bullets, but will still handle the 100gr Nosler Partition which he says is more than adequate for any British deer species including Scottish red stags.

Accuracy-wise, I don’t think there’s anything between them if everything else is equal. The 6.5 has a reputation for superlative accuracy, but that was high-quality Swedish military rifles and ammunition matched against often not-so-high-quality military stuff from elsewhere. Put the pair in custom rifles and use equally good brass and bullets and you’ll be hard pressed to tell them apart.” – Laurie Holland

After Laurie’s helpful comments, some other Forum members added their insights on the .260 Rem vs. 6.5×55 question:

“To me, the .260 Remington has no advantage over the 6.5×55 if one is going to use a long action. Likewise, the only advantage the .260 has in a modern rifle is it can be used in a short-action. There is more powder capacity in the 6.5×55 so you have the potential to get more velocity plus there is a lot of reloading data available to you for loading at lower velocity/pressure if you choose. The Lapua brass is great and Winchester brass is pretty good at low pressures. Having loaded a good bit for both, the 6.5×55 would always get the nod from me. To me, if someone wants to use a short-action, the 6.5×47 Lapua is even a better option than the .260 for a target rifle.” — Olympian

“There is just one small item that has been missing from this conversation — the 6.5×55 has a non-standard rim diameter of .479″ vs. the standard .473″ of a .308 and all of its variants. Depending on your bolt this may be an issue, or it may not.” — Neil L.

Other 6.5mm Contenders: 6.5×47 Lapua and 6.5 Creedmoor vs. .260 Rem
by Laurie Holland
Since I wrote those words some time back, I’ve acquired the three small contenders – .260 Rem, 6.5X47L, and most recently the 6.5mm Hornady Creedmoor and started doing load development and comparative tests. All three rifles have match-length barrels (28 or 30-inch 1:8s) — two NZ True-Flites and on the .260, a 30-inch 5R Bartlein.

How the barrel is throated is a key issue with this trio. In my case, I have always had the feeling that the .260 Rem and 6.x5x47L are at their best with 120-130 grain bullets and both have been chambered to suit the 123gr Scenar seated optimally. Both shoot this bullet fantastically well at getting on for 3,000 fps using Vihtavuori N150. I’m constantly amazed by this bullet’s external ballistics performance at up to 900 yards. I’ve yet to try it at 1,000. No, you won’t stand up to someone shooting a 7 WSM or .284 Shehane with 180gr Hybrids or VLDs at 900 or 1,000 in rough conditions in an F-Open match, but that applies to the 6.5-284 too.

I’m very taken with all three cartridges. The 6.5×47 Lapua is an outstanding mid-range number IMHO. The .260 a good all-rounder. But I have a ‘feeling’ that I am going to end up very fond of the Creedmoor and can understand its tremendous success in the USA. Over here in the UK, it barely registers with target shooters, and I doubt if at all with what US shooters call ‘hunters’, we call ‘deerstalkers’. Fortunately, I was able to get 300 pieces of Hornady brass a couple of years ago, but we can get very strong Lapua .22-250 Rem cases here easily and they can be necked-up / fire-formed albeit to produce a slightly short-necked 6.5 HCM.”

The Ruger Precision Rifle (RPR) has been a huge sales success. Nearly a year after its introduction, the RPR remains in very high demand. The first production run by Ruger essentially sold out, so it is very hard to find one for sale, in any caliber.

CLICK HERE for Large-format Ruger Precision Rifle Product Brochure (4mb PDF).

Though it has a big winner on its hands, Ruger has made some upgrades to its popular RPR. An “enhanced” RPR will be offered with a new handguard, bolt shroud, and muzzle brake. Two new models have been added to the RPR line-up, the model 18004 in .308 Win, and the model 18008 in 6.5 Creedmoor. These models, priced at $1599.00 MSRP, feature a new, low-profile handguard, a new aluminum bolt shroud, and a muzzle brake. The new handguard will work better for scopes with large front objectives. The muzzle brake should reduce felt recoil, but we do wonder whether accuracy might suffer. The brakeless, first-generation RPRs exhibited very good accuracy most of the time.

For the time being, the original model RPRs will be offered along with the new enhanced RPRs: “Both the original and enhanced configurations will be available from Ruger for a time, with the initial pattern being phased out as supplies are depleted.” (Source: American Rifleman). But there is a catch. The new models cost $200.00 more than Gen 1 RPRs. Ruger lists a $1599.00 MSRP for the enhanced RPRs versus $1399.00 for Gen 1 models.

To See NEW FEATURES, click the image below, then SCROLL down the page on the Ruger web page that loads. Yes, the VIDEO is there — you just have to scroll down.

According to American Rifleman, the new handguard has multiple benefits: “Still free-floating and KeyMod-compatible, the new design omits the original’s top-mounted Picatinny rail in order to increase scope clearance. Given the larger objective lenses utilized by long-range optics, this enhancement makes a lot of sense. The bottom surface of the new handguard is also contoured with a flatter surface, providing for a more stable foundation for the mounting of bipods than the original model.” Current RPR owners can purchase the new-style 15″ aluminum handguard for $249.95 from ShopRuger.com.

Ruger RPR Hybrid Muzzle Brake
The original, Gen 1 Ruger Precision Rifle had a threaded muzzle covered by a thread cap. The new “enhanced model” features a factory-installed “hybrid” brake fitted to the barrel. This brake combines radial holes in the rear half with large, angled side ports in the front. Ruger claims the brake reduces recoil almost 40% on a 6.5 Creedmoor. This brake can be purchased separately for $99.95 from ShopRuger.com.

The Precision Rifle Series (PRS) has introduced a new, price-capped Production Class in an effort to boost participation by making competition more affordable. Under recently-issued PRS rules, Production Class rifles may cost no more than $2000.00. The rules state:

“Production Division combined rifle and scope MSRP as listed on the company’s website shall not exceed $3,000 USD, the rifle shall not exceed $2,000 USD and the optic not exceed $2,000 USD.

Production Division rifles are not permitted to be altered or improved in any way from the original factory configuration.

In an effort to prevent exorbitant costs for beginning shooters, Production Division round count will not exceed 80 rounds.”

To fit the new Production Class Rules, MasterPiece Arms (MPA) has developed the new BA Lite PCR Competition Rifle built around a Savage Model 12 short action. Designed specifically for the new PRS Production Class, MPA’s PCR Competition Rifle offers many premium features yet stays under the $2,000 Class limit. The Savage action is upgraded with a Rifle Basix 2-lb trigger, and the adjustable, modular chassis offers a bag rider, barricade stop, and even a built-in bubble level. Bipods can be attached up front to a rail, with optional spigot mount. MPA PCR Rifles come with stainless Bergara barrels, 22-26 inches in length, fitted with MPA muzzle brakes (muzzle thread is 5/8-24 TPI).

MPA BA Lite PCR Competition Rifle Specifications:
Chamberings: 6mm Creedmoor, 243 Win, 6.5 Creedmoor, 308 Win, 6.5 x 47 Lapua, 6mm x 47 Lapua
Action: Savage Model 12 Short Action
Trigger: Rifle Basix Savage Trigger Set to 2 lbs.
Barrel: Bergara 416R Stainless Premium Barrel Blank
Chassis: MPA BA Lite Chassis
Muzzle Brake: MPA High Performance Muzzle Brake
Magazine: AICS Type (10 Round Accurate/AICS Type Magazine Included)
Chassis Weight: 2.9 lbs. (Overall rifle weight depends on barrel length and contour.)
MSRP: $1,999.99

Left-Hand and Right-Hand Models in Choice of Five Cerakote Colors
The MPA BA Lite PCR Competition Rifle is available in black, burnt bronze, flat dark earth, gunmetal, and tungsten in both left- and right-handed set ups. All chassis and barrels are Cerakoted® in a multitude of colors and patterns. (Custom patterns are $150.00 extra). Barrel lengths available include 22 inches through 26 inches. The barrel twist is caliber-specific and the barrel muzzle thread is 5/8-24 TPI.

Editor’s Note: While the MPA PCR Competition rifle has nice features, it’s hard not to compare it to the Ruger Precision Rifle costing hundreds less. The latest Gen 2 Ruger Precision Rifle, with a sleeker handguard and factory muzzle brake, is available for under $1500.00 “street price”. Ruger lists a $1599.00 MSRP for the Gen 2 RPR versus $1399.00 for Gen 1 models.

The NRA’s American Rifleman showcased an interesting project this week — an upgraded Ruger American Rifle Predator in 6.5 Creedmoor. The video below shows how a laminated wood stock from Boyd’s Gunstocks was adapted for the Ruger. A Boyds Prairie Hunter model in gray laminate was selected. This was custom-bedded to the Ruger’s action using Brownell’s Acraglas.

All Ruger American Rifle models employ dual aluminum V-Blocks to support the action. These fit slots in the underside of the action. Boyds makes its own version of these V-Blocks which were installed in the Boyds stock to secure the action.

Project leader Joe Kurtenbach says the size, shape, and geometry of the Boyds V-Blocks is very accurate, so they fit the Ruger action well. To further support the action, Acraglas bedding compound was applied to the inside of the stock, after release compound was applied to the barreled action. With this DIY bedding job, the Boyds laminated stock is definitely an improvement over this original “Tupperware” factory stock.

DIY Bargain Hunter Upgrade
American Rifleman states: “The Ruger American has some great features—hammer-forged barrel, reliable action, crisp trigger — but many would not consider the molded, polymer stock to be among them. Luckily, there are aftermarket options to enhance the rifle’s utility and aesthetics. A durable, attractive stock from Boyds Gunstocks and some DIY action bedding, using Brownells Acraglas, is the next step in the precision-driven hunting rifle build.”

Choice of Gun and 6.5 Creedmoor Chambering
For this project, American Rifleman’s Joe Kurtenbach selected one of his favorite cartridges, the 6.5 Creedmoor. Introduced in 2007 by Hornady, the accurate, flat-shooting 6.5 Creedmoor has proven very popular with both hunters and tactical/PRS shooters. The Ruger American Rifle Predator was chosen for its affordable price, reliable action, and Ruger Marksman adjustable trigger.

In this video, Kurtenback explains how and why the 6.5 Creedmoor chambering and Ruger American Rifle were chosen for the Precision Hunter rifle build project.

Here’s an item for tactical and Precision Rifle Series (PRS) shooters. Howa is releasing a new rifle with a modular metal chassis. The new Howa HCR (Howa Chassis Rifle) combines a Howa 1500 barreled action with a modern, fully-adjustable aluminum chassis. The Howa’s MSRP is $1299.00, so the HCR is directly competitive with the Ruger Precision Rifle (RPR). Available chamberings are: .223 Remington, .243 Winchester, 6.5 Creedmoor, and .308 Winchester.

Mounted on an AR-style buffer tube system, the Howa HCR utilizes the fully adjustable LUTH-AR MBA-3 stock. Length of Pull is adjustable form 12.5″ to 16.75″. Comb height is also adjustable to fine tune for scope height-over-bore. Weight with a 24″ barrel is 10.2 pounds (before optics), so this Howa HCR is lighter that some similar rifles on the market.

Howa HCR Features

• Howa 1500 Barreled Action with 20″ and 24″ Heavy Barrel options
• Black 6061-T6 Aluminum Chassis with Free-Float M-LOK Forend
• LUTH AR Buttstock with LOP Adjustment (12.5″ to 16.75″) and Adjustable Comb
• 10-RD ACCURATE Detachable, Teflon-coated Steel Magazine
• Two-Stage H.A.C.T. Trigger
• 3 Position Safety

The HOWA HCR features an adjustable, two-stage HACT trigger, set for about 3 pounds (combined stages). Crisp and repeatable, this is an excellent trigger for a factory gun. In our opinion, the HACT trigger is clearly superior to the trigger on the Ruger RPR, as well as the Savage AccuTrigger. And there is no annoying Glock-style safety lever in the middle of the trigger blade.

Available in .223 Rem, .243 Win, 6.5 Creedmoor and .308 Win chamberings.

NOTE: For all chamberings, 24″ barrels are offered, with 20″ options for the .223 Rem and .308 Win as well. Twist rates are 1:9″ for .223 Rem, 1:10″ for .243 Win, 1:8″ for 6.5 Creedmoor, and 1:10″ for .308 Win. We think .243 Win shooters will NOT be happy with the 1:10″ twist. We would prefer to see a 1:8″-twist for the .243 Win so it can shoot the 105-115 grain 6mm bullets. Most competitive 6mm shooters will want a true 8-twist or even a 1:7.5″.

Here’s an important announcement for anyone who uses a powder in the 4350 range. Alliant is now shipping the all-new Reloder 16 powder. The burn rate is slightly faster than Reloder 17, and a bit slower than Varget or Reloder 15. Notably, this new Reloder 16 powder is very temp stable. AccurateShooter.com was shown “top secret” test results comparing Reloder 16 with other popular propellants, including Hodgdon Extreme series powders. The results for Reloder 16 were remarkable. Reloder 16 showed extremely constant velocities even with very high ambient temps — so this is a powder you can shoot even on hot Arizona summer days.

This is NOT just a slower version of Alliant’s double-based Reloder 15 (which words great in the 6mmBR and Dasher cartridges). Reloder 16 is a completely new formulation, produced in Sweden by Bofors for Alliant. Reloder 16 utilizes TZ technology, which manipulates the response of the propellant and resists the natural tendency to generate more pressure at higher temperatures and less pressure at lower temperatures.

As a result, Reloder 16 offers outstanding temperature stability. Based on the test results we’ve seen, if you are using H4350 or IMR 4451 currently, you should definitely give Reloder 16 a try. The powder also boasts excellent lot-to-lot consistency and contains a proprietary de-coppering additive.

Match and Hunting Cartridge Applications:
Alliant tells us that Reloader 16 “is ideal for traditional hunting cartridges, such as .30-06 Springfield and .270 Winchester, as well as 6.5mm target loads and tactical applications wherein temperature stability is required.” We also think the powder may work very well in these popular match cartridges: 6XC, .243 Win, 6.5×47 Lapua, 6.5 Creedmoor, .260 Rem, .284 Win, and .300 WSM. For example, Alliant’s Load Data Sheet shows a 2772 FPS load with 142gr SMKs in the .260 Rem.